Hanging your wallpaper is easy when you have superior instructions to follow. Is it time to update your home or office?

If you are new to wallpaper then pay attention to the kind of wallpaper you are drawn to when selecting. Determined by which kind you decide on, there may be some varied installation methods. Pre-pasted selections are outfitted with a dry paste which is on the surfaces’ backside. This is triggered by using water, as opposed to unpasted wallpapers need a wet paste employed with installation. Generally, the process is the same for installing, however, the instructions may differ depending on which type.



Measure, cut, activate with H20 or paste and hang are the general guidelines for installing wallpaper.

Wall Preparation

It is important to work with tidy surfaces and a clear workspace before you begin. Make certain all electrical outlets are turned off and take off any wall fixtures. Clear away any previous wallpaper paste or deposits and clean the walls thoroughly with TSP before getting started.

Ready your wall employing a premixed universal primer for wallpaper. If you are applying unpasted wallpaper, priming the wall is essential to facilitate easier removal.

Measure & Activate the Paper

Start by computing the length of the wall. After you have that measurement, add four inches and then cut the wallpaper. Ideally, you would like the paper overlapping at the baseboard and the ceiling by approximately two inches.

Pro Tip: Allow for pattern match, via drop match, straight across or random.



If hanging unpasted wallpaper…

You can either apply the paste to the wall surface or paste the paper. If you apply the paste to the wall, cover the area for one strip only and be sure to apply the product evenly. If you opt to paste the paper, work from the centre to the edges and equally coat the rear of the wallpaper. Then loosely fold the moistened strip, pasted sides alongside one another and let sit for three minutes. This is whats called booking.

Note that if you are pasting unpasted wallpaper, you may paste the paper or the wall itself. Ensure that you only paste one area of the wall at a time when you are pasting the wall. If you're putting on paste to the wall, only paste one segment at a time. If you are employing the paste to the paper, put an even layer of paste on the wallpaper backing. Begin sticking in the middle of the wallpaper and move toward the edges. Delicately fold the moistened wallpaper strip and maneuver the pasted sides together so the booking strategy can take place. Let this folded booking of wallpaper rest in this position for three minutes.

Pro Tip: If hanging up heavyweight wallpapers, particularly unpasted styles with flock, cork, or embroidery, select a clear, stain-free heavyweight pre-mixed paste adhesive instead of a light-medium weight clear paste for optimum results.

When hanging pre-pasted wallpaper…

Take your cut strip and roll it loosely with pasted side out and patterned side in. Next, submerge the rolled strip for 30 seconds into warm water to activate the paste. You may also rely on a wallpaper hand sprayer that secretes a fine water mist to activate the pasted portion.

If you utilize the hand sprayer, spray in prolonged strokes that are the length of the paper to fully moisten the back of the strip. Make sure you focus on the edges to ensure even water application. Have the pasted sides together by folding each section of the strip toward the center. Ensure the edges don’t dehydrate by precisely aligning the sides. Last, roll your strip like you would roll a newspaper and enable it to sit for three minutes so the paste can initialize while the paper grows more flexible.



Hanging your first strip

Move your strip to the wall when the booking process is complete after three minutes. Slowly unfold the item and hang it. Allow the product to overhang on the ceiling and the baseboard. Clear away any air bubbles by using a smoothing brush or wide knife or a plastic smoother. Press on the wallpaper to allow for adequate contact and adhesion to the wall. Take care not to pull or distort the wallpaper. Make use of a seam roller to softly flatten the seams.

Proceeding to the second strip

To apply the 2nd strip, butt it up alongside the edge of the first wallpaper strip. Firmly and smoothly press the wallpaper into position. Ensure that you wash the ceiling and the baseboard after to remove any residual paste. Ideally, your seams should really be vertical with a tight fit. You want everything free of paste and air bubbles.

Once you have installed three panels smoothly to the wall and removed excess paste, take a moment to examine your work. Check the sheets for color and design uniformity. Carry on installing three panels by doing this at a time. Matching patterns or geometric designs might require extra selvage trimming to create colour coordinating across seams. As soon as your eyes and arms are tired, take a break and have some rest. Never hurry a wallpaper assignment. Displaying your strips in this technique can help you achieve uniform results. Once you're finished, cut the extra trim along the baseboards and ceiling carefully. To successfully remove excess wallpaper without tearing, use a guide and a razor knife.